In order to install ssd / ram on the intel nuc skull model, you have to turn four screws.
However, there are problems with these four screw sockets.
I have two nuc skull models
One is that two of the four screw sockets are damaged and two have fine cracks.
The other has no damage, but there are marks that are cracked finely.
(Perhaps it seems that you can loosen and tighten the screw a number of times.)
It is a chronic problem Will other users have such a case?
Or I am not lucky ??
I just got a nuc6i7kyk and I'm trying to set up a RAID through BIOS. I have two identical Toshiba OCZ RD400 SSDs installed. BIOS can see both of them.
I followed the directions (RAID Setup Procedure for Intel® NUC Kit NUC6i7KYK ) and set up the two drives initially:
Advanced -> devices -> SATA ->
"Chipset SATA Mode" -> RAID
M.2 Slot 1 RST PCIe Storage Remapping -> checked
M.2 Slot 2 RST PCIe Storage Remapping -> checked
Then saved, quit, and re-loaded BIOS. I then entered the Intel Rapid Store Technology Add-in config:
Advanced -> devices -> Add-in Config -> "Intel(R) Rapid Storage Technology" -> configure
And then all it shows is:
Intel (R) RST 14.8.0.2377 RAID Driver:
No disks connected to system
BIOS can see the drives, they're both "remapped to RST," but Intel RST can't see them to build an array out of.
Any help would be much appreciated.
KkThnxBai.
Intel's decision to run the SD reader over PCI is great; but the lack of UHS-II support defeats the purpose. Could you please add UHS-II support to future NUCs.
My Intel NUC NUC6i7KYK, running Windows 10, seems to not see my Thunderbolt 3 external HDD after a reboot. I have all drivers up to date as is the bios.
The external drive is the Akitio Thunder3 Duo Pro. If I go to device manager and scan for hardware changes it picks up the device and it appears as normal in Windows Explorer.
Anyone else seen this before and if so any way to resolve this.
Thanks - Tony
Hello,
My NUC6i5 with graphics driver V15.45.2.4481 displays 64x64 pixels mosaic when all the following conditions are matched:
1. Use hardware video decoder (DXVA), and,
2. The video file is H.265 8-bit encoded format, and,
3. The width of the video is 1920.
The issue is also found in previous driver versions.
The issue is not found for H.264 format, nor 10-bit H.265, nor 720p, nor 4K video.
Here is a example video: http://video.h265files.com/video-h265.mkv
and the screen shoot of upper left corner:
Hi there
Issue:
I have UHD enabled in TV as well as using the HDMI/PC input. Had absolutely no issues with old PC with Nvidia 960GT with YCbCr 4:4:4 enabled. Using same HDMI cable which is supposed to be 2.0 compliant. I tried another cable (which was same brand) but same issue.
Skull Canyon is brand new and installed with Win10 64bit, latest 0042 bios, latest 4542 graphic divers. I also did the HDMI firmware update when connected to my TV. It already had the latest version but updated again.
TV running at 4K 3840 × 2160 at 60Hz.
Does this NUC support YCbCr at 4:4:4, because even with YCbCr enabled I seem to be getting a bit of black crush compared to nvidia?
Any thoughts on the weird colour as well? I've attached a couple of pics which illustrate the problem?
Paul
Intel BOXNUC6i7KYK1 with Crucial Ballistix Sport LT 32GB Kit (2 x 16GB) DDR4-2400 SODIMM
Everything installed and worked fine…but after about 5 minutes, the NUC6i7KYK turns off then re-starts. After it turns back on by itself, it asks to edit the BIOS. Answering NO, the system re-boots and is stable with no issues.
Same thing happens with DDR4-2133 memory, which is completely compliant with the NUC6i7KYK memory specification. The NUC6i7KYK shuts down after the first 5 minutes then restarts.
Please advise on how to get the Intel NUC6i7KYK to operate without the very annoying automatic restarts!
Thank you very much!
Message was edited by: lonzo54
Hi
I have NUC6i3SYH with Libreelec installed
I'm looking for a detailed remote control setup guide
I would also like to get remote controller suggestions (feature, type, kind, brand, ...)
Are there any specific requirements?
Any details will be appreciated
Thanks!
Hi guy,
I have a problem with NUC UN42.
When I connect many devices to NUC box via USB3.0 port. I get a kernel log.
Dec 26 07:47:28 user-UN42 kernel: [ 392.795797] usb 2-5.2.3: Not enough host controller resources for new device state.
Dec 26 07:47:28 user-UN42 kernel: [ 392.795807] usb 2-5.2.3: can't set config #1, error -12
Dec 26 07:47:29 user-UN42 kernel: [ 393.782404] usb 2-5.2.3: Not enough host controller resources for new device state.
Dec 26 07:47:30 user-UN42 kernel: [ 394.784502] usb 2-5.2.3: Not enough host controller resources for new device state.
Dec 26 07:47:31 user-UN42 kernel: [ 395.786654] usb 2-5.2.3: Not enough host controller resources for new device state.
Please let me know how to fix this problem !
Many thanks !
P/S:
My system information
00:00.0 Host bridge: Intel Corporation Haswell-ULT DRAM Controller (rev 0b)
00:02.0 VGA compatible controller: Intel Corporation Haswell-ULT Integrated Graphics Controller (rev 0b)
00:03.0 Audio device: Intel Corporation Device 0a0c (rev 0b)
00:14.0 USB controller: Intel Corporation Lynx Point-LP USB xHCI HC (rev 04)
00:16.0 Communication controller: Intel Corporation Lynx Point-LP HECI #0 (rev 04)
00:1b.0 Audio device: Intel Corporation Lynx Point-LP HD Audio Controller (rev 04)
00:1c.0 PCI bridge: Intel Corporation Lynx Point-LP PCI Express Root Port 1 (rev e4)
00:1c.1 PCI bridge: Intel Corporation Lynx Point-LP PCI Express Root Port 2 (rev e4)
00:1c.2 PCI bridge: Intel Corporation Lynx Point-LP PCI Express Root Port 3 (rev e4)
00:1d.0 USB controller: Intel Corporation Lynx Point-LP USB EHCI #1 (rev 04)
00:1f.0 ISA bridge: Intel Corporation Lynx Point-LP LPC Controller (rev 04)
00:1f.2 SATA controller: Intel Corporation Lynx Point-LP SATA Controller 1 [AHCI mode] (rev 04)
00:1f.3 SMBus: Intel Corporation Lynx Point-LP SMBus Controller (rev 04)
03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 11)
Hello I just want to share my experience with this curious issue on Intel NUC5i7RYH.
Running Ubunutu 16.04 with TPLINK AP getting the 2.4Ghz signal of WIFI access, after some troubleshooting on why the ICMP time response to AP is above 2 secs and having bad performance of navigation, I turned off my embedded bluetooth in the NUC (the way I was listening my audios) and the issue was fixed completely.
Based on that we noticed NUC systems always will have two challenges that impacts negatively in 2.4Ghz WiFi connection: Bluetooth and USB3.0 ports also, NUC is a good system but having those two components inside the same WiFi antennas, you potentially will be affected in WiFi performance. Some threads refers to WiFi performance so it probably is the first stage to resolve it.
Hope it helps to the community of NUC,
Edgar M.
Hello I can't manage to run 3840x2160 at 60hz from my NUC.
I have a converter from mini DP to HDMI 2.0 and then a HDMI 2.0 cable to my tv.
60 hz works with this setup if I use my laptop instead (which has a mini DP).
Both are running pretty much identical systems of Arch Linux.
Any clues to why this fails?
Intel Team - I am struggling with a fresh WIN7 install of SSDM.2 Samsung EVO 850 - cannot get past driver selection
May the Wi-Fi card installed in NUC 5PPYH be replaced with another Intel's one, e.g. Wireless-AC 7265NGW?
I don't quite understand how to use bluetooth on subunit. Do I need a drive over or what? Can some one please tell me.
@[Intel Corporation]
Hi~ i have intel nuc6i7kyk, Win10x64, Bios 0042, samsung ssd 512G, 32G mem, two display 1.Dell U2515H 2K max 2560x1444 60hz 2. Samsung U28E850R 4K max 3840x2160 60hz ( 4 port: HDMI1 3840x2160 30Hz, HDMI2/DP/MINIDP 3840x2160 60Hz)
the NUC working on Dell display was perfect.
working on my new display Samsung worse, give me a big problem.
Cable1 Hdmi2.0 with Samsung display package. Cable2 Hdmi2.0 SAMZHE. Cable3 MiniDPtoDP with Dell display package. Cable4 MiniDPtoDP with Samsung display package.
NUC Hdmi to Samsung U28 Hdmi2 3840x2160 60Hz , if do nothing. just fine. but , if doing some works, screem start flash... please see video 1 -> Cable1/2
NUC Hdmi to Samsung U28 Hdmi2 3840x2160 30Hz , fine. even WoW and watch moives and use msword with hardware accelerate all together. -> Cable1/2
NUC Hdmi to Samsung U28 Hdmi2 2560x1444 60Hz , without hardware accelerate software was fine. no WoW, no msword with hardware accelerate, watch movie is fine. -> Cable1/2
NUC minidp to Samsung U28 DP 4K/2K 60Hz , worse. wil lost signal black screem, and recover. -> Cable3/4
NUC Hdim/MiniDP to DELL U25 2K 60Hz, All fine. -> Cable1/2/3/4
The Samsung display was ok, seller test with Graphic GTX960.
Graphic drive update to newest and older still problem.
seller said 4k display need higher support with graphic. differ structure with 2k.
can somebody help me to solve this problem?>
I'm getting a mini PC - Intel NUC Skull Canyon, but I am not what I should look for when buying a SSD for it.
I found these couple of SSDs below but not sure they are the right one for Intel NUC Skull Canyon:
1.
SanDisk Z400s SD8SNAT-256G-1122 M.2 SATA 2280 256GB Internal Solid State Drive (SSD)
2.
Intel 600p M.2 2280 256GB SSD PCIe NVMe (Read:1775MB/s, Write:560MB/s)
3.
Samsung 950 PRO NVMe M.2 256 GB Solid State Drive
SanDisk Z400s is the cheapest but it has no NVMe. So is it good or not? What is Z400s?
Which is better among these 3 options?
I just got a nuc6i7kyk and I'm trying to set up a RAID through BIOS. I have two identical Toshiba OCZ RD400 SSDs installed. BIOS can see both of them.
I followed the directions (RAID Setup Procedure for Intel® NUC Kit NUC6i7KYK ) and set up the two drives initially:
Advanced -> devices -> SATA ->
"Chipset SATA Mode" -> RAID
M.2 Slot 1 RST PCIe Storage Remapping -> checked
M.2 Slot 2 RST PCIe Storage Remapping -> checked
Then saved, quit, and re-loaded BIOS. I then entered the Intel Rapid Store Technology Add-in config:
Advanced -> devices -> Add-in Config -> "Intel(R) Rapid Storage Technology" -> configure
And then all it shows is:
Intel (R) RST 14.8.0.2377 RAID Driver:
No disks connected to system
BIOS can see the drives, they're both "remapped to RST," but Intel RST can't see them to build an array out of.
Any help would be much appreciated.
KkThnxBai.
I have four NUC6i7KYK NUCs using the Intel SSD 600p series drive & the G.SKILL Ripjaws Series 8 GB pn: F4-2133C15S-*GRS ram.
I am using an Aver CAM520 USB PTZ camera. The issue is I lose good video when I connect the camera with a USB Extender. The camera works fine with a short 10 ft USB cable.
The system is Win 10 Pro with the latest Intel BIOS & Drivers.
Does anyone know of a USB Extender that works?
The USB Extender works fine using an older computer.
Thank you
Hi Support and all
I own a Intel® NUC Kit D54250WYK
I have followed the method Using Fast Boot in Intel® Visual BIOS 2.x but not able to perform disabled fast boot with the instruction stated as Link.
Can kind soul assist me .
I need to change my BIOS setting to do reinstallation of OS
Thanks
Hi guy,
I have a problem with NUC UN42.
When I connect many devices to NUC box via USB3.0 port. I get a kernel log.
Dec 26 07:47:28 user-UN42 kernel: [ 392.795797] usb 2-5.2.3: Not enough host controller resources for new device state.
Dec 26 07:47:28 user-UN42 kernel: [ 392.795807] usb 2-5.2.3: can't set config #1, error -12
Dec 26 07:47:29 user-UN42 kernel: [ 393.782404] usb 2-5.2.3: Not enough host controller resources for new device state.
Dec 26 07:47:30 user-UN42 kernel: [ 394.784502] usb 2-5.2.3: Not enough host controller resources for new device state.
Dec 26 07:47:31 user-UN42 kernel: [ 395.786654] usb 2-5.2.3: Not enough host controller resources for new device state.
Please let me know how to fix this problem !
Many thanks !
P/S:
My system information
00:00.0 Host bridge: Intel Corporation Haswell-ULT DRAM Controller (rev 0b)
00:02.0 VGA compatible controller: Intel Corporation Haswell-ULT Integrated Graphics Controller (rev 0b)
00:03.0 Audio device: Intel Corporation Device 0a0c (rev 0b)
00:14.0 USB controller: Intel Corporation Lynx Point-LP USB xHCI HC (rev 04)
00:16.0 Communication controller: Intel Corporation Lynx Point-LP HECI #0 (rev 04)
00:1b.0 Audio device: Intel Corporation Lynx Point-LP HD Audio Controller (rev 04)
00:1c.0 PCI bridge: Intel Corporation Lynx Point-LP PCI Express Root Port 1 (rev e4)
00:1c.1 PCI bridge: Intel Corporation Lynx Point-LP PCI Express Root Port 2 (rev e4)
00:1c.2 PCI bridge: Intel Corporation Lynx Point-LP PCI Express Root Port 3 (rev e4)
00:1d.0 USB controller: Intel Corporation Lynx Point-LP USB EHCI #1 (rev 04)
00:1f.0 ISA bridge: Intel Corporation Lynx Point-LP LPC Controller (rev 04)
00:1f.2 SATA controller: Intel Corporation Lynx Point-LP SATA Controller 1 [AHCI mode] (rev 04)
00:1f.3 SMBus: Intel Corporation Lynx Point-LP SMBus Controller (rev 04)
03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 11)
