The Ram specs are:
Kingston - DDR4 - 16 GB - SO-DIMM 260-pin
2133 MHz (PC4-17000) 1.2V
Will this work even though NUC8i7HVK lists as supporting 2400HZ+?
↧
Will a Ram stick with 2133HZ speed work with NUC8i7HVK?
↧
Hard crashes NUC8i7HNK with clean Windows 10 Home install
Hi all,
Just received my new setup with Intel NUC8i7HNK. To get started quickly I first created an image of my old workstation (Intel NUC D54250WYK), but got hard crashes. Had to use the power button for a couple of seconds to reboot the machinTwo days ago I installed Windows fresh with all recent drivers (all from intel site) and bios (0040). Still have crashes. Even when only browsing with firefox with no other applications open.
Added components:
Memory: Kingston ValueRAM - DDR4 16GB - SO DIMM - 260PIN - 2400Mhz / PC4-19200 - C
SSD: Intel SSD 720p 256GB
Display: Dell Ultrasharp U3818DW
Keyboard/Mouse: Dell premier wireless
Please see output of ssu and ipdt attached. Hope someone knows the answer.
Best regards,
Bas
↧
↧
NUC7PJYH Samsung M471A5244BB0-CRC Dual-channel ?
I am using NUC7PJYH BIOS Version 0039 - JYGLKCPX.86A.0039.2018.0528.1436
I have a question
Samsung M471A5244BB0-CRC M471A5244BB0-CRC | Samsung Semiconductor Global Website
I attach two pieces and operate it but the operation speed of the memory is slow. Are you moving on a single channel?
Memory tested Dual-channel operation confirmed in other environments
M471A5244BB0-CRC I realized that Intel has not been tested Intel® Product Compatibility Tool
↧
NUC8i7HVK - No Undervolting Enabled
I recently bought NUC8i7HVK and the CPU runs really hot.
I've disabled Turbo Boost for now but this is no solution in the longer term.
My Question: Why aren't we allowed to undervolt CPU Vcore?
Can you please fix this with a bios update?
↧
NUC7i5BNK Thermal Event Hibernation
I am getting this error when i visit certain sites or use Steam: "The system was hibernated due to a critical thermal event."
All the drivers and BIOS are updated.
I just disabled Boost in the BIOS, but its still happening.
The system was hibernated due to a critical thermal event.
Hibernate Time = 2018-01-28T06:47:51.992734900Z
ACPI Thermal Zone = \_SB.PCI0.LPCB.H_EC.TZ0
_HOT = 200K
Amy recommendations? This thing is brand new.
↧
↧
How to get icls client version 1.47.715.0 for NUC6CAYS ?
Hi,
I downloaded the latest BIOS (AY0050.bio) to address the SA-00086 vulnerability.
When I run the SA-00086 Detection Tool, the error message I get is that ICLS is obsolete. Minimum required version is 1.47.715.0
How would I get icls client version 1.47.715.0 ?
Please see attachment for full message from SA-00086 Detection tool.
Thanks,
Nelson
↧
NUC 7i5BNH does not output 4K@60p with 10-bit YCbCr420 color + HDR
Hi all,
Just got myself a new LG 65B7 TV
Hooked my NUC to it - it switched to 4K automatically.
I has also able to change the output to 60Hz via the Intel management utility.
However, I do not see an option to change the color depth or format.
I saw some screen captures in other topics where people have an "advanced" in the "display" menu - while I do not.
Is it something I have to enable somehow?
Maybe the missing settings are hiding there...
Anyway, my current settings are stuck at 4K@60p with 8-bit YCbCr420, and I do not see any way to change those.
Updated the graphics drivers, flashed HDMI firmware, flashed BIOS, Windows is updated to the creators update.
Regarding HDR - I do see the toggle - but when toggled - it just goes back to being off.
Any advice would be greatly appreciated!
↧
actual nuc5cpyh not boot from sd, older can
Hi all,
in 04 Feb 2016 I bought a NUC5CPYH. From the beginning it boots from SD an Ubuntu without any other storage. Days ago, the device dies i don't know why, it runs for a few minuts and then nothing. Well, it has been working fine so i decide to buy the same model again, plug the memory, the SD and try to boot. It shows the typical message that can't find a bootable device. No problem, i get into the BIOS and ... i can't see the SD card in any option. The broken NUC5CPYH comes with the Visualbios 2.2.16 and the new one with the 2.2.20 version. Then, need i to do a downgrade to get the SD boot option?
↧
NUC8i7HVK faulty usb-c video drivers
I've setup my hades canyon nuc (NUC8i7HVK) with all the latest drivers and bios and the performance of my monitors when driven by the thunderbolt/usb-c output is awful. The monitors have a native resolution of 2650x1440, but the NUC will only drive them at 2048x1080. Using the mini-display ports doesn't fair any better. In both cases the rendering lag is 300ms - 2 seconds depending on the task.
Also, the time to negotiate the connection takes 4-10 seconds (if it even displays at all).
The monitors work perfectly and instantly when plugged into the usb-c on my macbook pro.
↧
↧
No HDMI audio and video flickering issues 8i7HNK1
i purchased a new Hades Canyon, and started using it today. Already I’ve encountered a few major issues, and I think I’ve seen threads from other people with similar problems.
Firstly, when using an hdmi output, the computer fails to recognize the television(or monitor, I tried both)as being available. The headphone jack works fine, but neither of the hdmi outputs seem to work. I’ve tried multiple screens as well as different hdmi cables.
Secondly, when attempting to watch a video, more often than not I’m seeing a large amount of video flicker. Videos streamed in iTunes are al,ost unwatchable because of this. Videos off of an external hard drive I have are better, but still not good.
I have Windows 10 home installed, and have updated to bios 40(the latest one I could find for this unit).
↧
audio device disappearing
All,
I've seen a few threads related to my issue but no solution that I found
https://communities.intel.com/thread/108325
https://communities.intel.com/message/453487#453487
I have exactly the same issue where audio device disappears when amplifier and/or TV is turned off. I have 2 new NUC7i5bnh with updated bios/drivers etc. And, I get the problem on 2 different setups (1 going to onkyo receiver; 1 going to Samsung TV directly). Is there a solution here?
Using this as an HTPC for my mom. Right now it's hooked up HDMI into her receiver, which then of course connects to her TV HDMI. It works great, no problems, until she stops for the night and turns off her TV and Receiver. When this happens, the NUC (Windows 10 x64) shows the speakers are disconnected. Since the receiver is off, and the audio device is the HDMI, that makes sense. The problem is it doesn't come back when everything gets turned back on. We have to reboot the NUC to get it to recognize it again, and this gets annoying because it kills the VPN and I have to remote in and reconnect it and so on and so forth. The audio device still shows up in device manager, but does NOT show up at all under playback devices, even as a disconnected device. Any ideas?
↧
No display signal for initial NUC setup.
I ran a search on this forum for a no signal issue with the NUC and didn't find an answer for my problem. I just purchased the NUC8i7HVK today. I installed the hard drive as well as the memory. When I power the unit on, my monitor gives me a no signal message. I'm using an HDMI cable and it doesn't show up. I used a display port cable and it still doesn't show up. Both cables work fine when I connect them to my older Skull Canyon NUC6i7KYK. Can anyone shed some light on this issue? The bios screen does not appear because there is simply no signal in the first place.
Thanks in advance
↧
D54250WYKH thermal pad
Just upgraded Intel NUC Kit D54250WYKH with Crucial MX500 500GB SATA 2.5-inch 7mm (with 9.5mm adapter) Internal SSD (CT500MX500SSD1) and experiencing high hard drive temperatures (over 50C).
Raised fan minimum duty cycle and managed to lower HDD temperature to 48C per instructions:
https://www.intel.com/content/www/us/en/support/articles/000005914/mini-pcs/intel-nuc-kits.html
Since D54250WYKH is discontinued and does not have the thermal pad already installed, how/where to purchase thermal pad for it?
I understand thermal pad should stick to chassis, but when closed it should slightly touch SSD which is 7mm (thinner than original 9.5mm).
Anybody aware of what exactly thermal pad should I purchase to resolve high SSD temperature?
Many thanks.
↧
↧
integrated Digital microphone array (DMICS) doesn't work after update Realtek drivers
the integrated Digital microphone did worked when I install Win10 at first, but if I install the "Realtek* High Definition Audio Driver for Intel® NUC Kit NUC8i7HNK, NUC8i7HVK" version 6.0.1.8323 provided, the microphone stopped working, I tried several times ,same results.
So i had to uninstall intel driver and then install the realtek HD audio driver from the realtek's own website, http://www.realtek.com.tw/downloads/downloadsview.aspx?Langid=1&PNid=14&PFid=24&Level=4&Conn=3&DownTypeID=3&GetDown=false, it really worked and saved my microphone back, but without the Realtek HD Audio Manager, anyone surfer same problem ? How can I got the microphone and the realtek audio manager worked same time?
↧
NUC5i3RYH 3 blinks, won't boot
Hello
My NUC stopped booting and the screen stays black.
The blue power led blinks 3 times, which seems to indicate a RAM issue (it used to work just fine).
I swapped the RAM stick with 2 others, different brands but both 1.35V, and tried in the 2 RAM slots. Still nothing.
A clear CMOS didn't help either.
The power supplies delivers 19.4V, the 5V, 3.3V and 1.35V on board are present.
Is there a troubleshooting procedure for the Serial presence detect (SPD) ?
Many thanks
Romain
↧
NUC8i7HVK fans speed control - resonating
Is there any possibility to set uneven speed for fans? At some point of speed they start to slightly resonate which cause unnecessary increase of noise. If it goes beyond this speed it is back again more quiet.
I would rather want to avoid stuff like Low Noise Adapters so software/bios control will be better (if possible)
Thanks
↧
NUC7i5BNHXF-Taskbar ICONS Missing on extended display(TV)
I have the following setup.
Main Display is a 27" 1920 Monitor attached to Thunderbolt port with USB C to HDMI (Samsung)Cable, NO Problems
Extended Display is a 55" Sharp 1920 TV attached to the HDMI port.
If I set up system to Duplicate Display there is no problem I get all app Icons on Both Displays.
In Extended Mode The following happens
If TV is Turned on HDMI or Normal TV and I boot up the NUC The ICONS are there on the TV Taskbar.
If TV is off when I boot up the NUC The ICONS are missing on the TV Taskbar(unless you are in Duplicate mode).
Same issue when NUC wakes up from sleep.
I found a quick way to get the ICON's back, Right click on taskbar and toggle - Show task view Button- or any other one and they come back.
I have tried every conceivable setting in BIOS also tested different HDMI cable but to no avail. Win 10 PRO with all the display settings correctly......
I DO NOT WANT DUPLICATE DISPLAY.
Does anyone know how to fix this?
↧
↧
Latest BIOS 0064
Updated my NUC7i5BNHXF BIOS to 0064 using the F7 file and Method. No Problems encountered.
↧
Failures of Intel(R) Display Audio on NUC
I'm having a terrible time with HDMI on my new NUC. Hours of searching and research have revealed others having similar issues, but those threads always seem to end without resolution. Frustrating.
I have the NUC7i5BNK J31144-309 HDMI port connected to an HDMI 2.0 port on a new LG43UD79 4K monitor 3840x2160 30Hz, Win10 display scaling either 100% or 150%. The NUC BIOS is updated to latest BNKBL357.86A.0063.2018.0413.1542, and I have tried setting the BIOS default display to either AUTO or HDMI. I have simultaneously removed both drivers, rebooted, and let Win10 re-install them. They are the latest available (April 6) versions including Intel(R) Iris(R) Plus Graphics 640 version 24.20.100.6025 and Intel(R) Display Audio version 10.25.0.5.
My NUC is set never to sleep. Whenever the monitor is blanked and turned off, or if the input source on the monitor is switched to another computer, there is no audio when the monitor is restored. The volume control system icon reliably has a red 'x' on it, and there is no corresponding playback device. Going to the Device Manager for Intel(R) Display Audio and using Disable followed by Enable sometimes resolves the issue. Other times, a reboot is required.
This is evidently a long term problem that has not been addressed by Intel but should be easy to reproduce. I also have the problem of all windows getting shrunk to the upper left all the time, but the audio problem is pretty much a show stopper for trying to replace my 8-year-old old Win10 tower with a NUC. System Support Utility output is attached. I could really use some suggestions for things I haven't tried yet.
Thanks,
Curt
↧
NUC7PJYH2 not booting
Hi,
i brought today a NUC7PJYH2 with following compontens :
- 250GB Crucial MX500 2.5" (6.4cm) SATA 6Gb/s 3D-NAND TLC (CT250MX500SSD1)
- 8GB (2x 4096MB) HyperX Impact DDR4-2400 SO-DIMM CL14-14-14-29 Dual Kit
when i switch the nuc on i have a black screen and the blue light blinks 3 times after 1-2min the nuc turns off and boot again.
looks like an issue withe the ram.
is there any change to get run the system with this ram or i schould buy another ram ?
↧