Quantcast
Channel: Intel Communities : Discussion List - Intel® NUC
Viewing all 18668 articles
Browse latest View live
↧

Graphics issues with NUC7I7BNH

September 11, 2017, 11:04 am
$
0
0

I have the NUC7I7BNH running:

 

  • Windows 10 Home (64 bit),
  • Kingston HyperX Impact 2x16GB  2133 MhZ DDR4 RAM
  • Samsung 960 EVO 250GB M.2 SSD
  • Connected via HDMI to LG 27UD69P-W 27" monitor

 

Two primary issues:

  1. When the monitor goes to sleep, I can't wake it back up without turning off the computer.  This seems to be an issue with the Intel GPU?  I've seen this issue on many forums with no real answer.  This alone is incredibly disappointing and if I hadn't bought all of these components to go along with my machine I'd be returning it unless I can find a solution that allows my monitor to sleep and wake up properly.
  2. When running google chrome, and going to google maps, the computer sounds like it is a jet engine taking off and starts going extremely slowly.  This problem does not exist with MS Edge, only in Chrome.  Not sure what could be causing this?

 

Thank you!

↧
Search

NUC6i3SYH Video and Audio Issues

August 28, 2017, 8:24 am
$
0
0

I have a NUC6i3SYH (16gb Crucial DDR4 2133RAM (2x8GB), 256GB Intel M.2, 27" LG 27UD58 Monitor running up to date windows 10) and have 2 issues with it:

 

1. The audio: on first boot the audio doesn't work. If you restart the computer (which takes an age if the audio isn't working) it will work when it re-starts. This is just mildly annoying and never used to be like this. Is this something windows update has broken? I have updated the bios to SY0061.BIO as I was running one 57 or something equally old and it's not made any difference? Windows normally boots in a matter of seconds and when the audio is working restarts very quickly.

 

2. I'm getting some flicker on part of the screen. I'm unclear if this is down to the monitor or the gpu? It's a fairly recent problem and seems worse if the computer has been on for a while making me wonder if it's an issue with the GPU and heat? Where is the best place to start trouble shooting this issue? Or is it a known issue with the NUC?

 

Thanks in advance.

 

Dave

 

↧
↧

NUC kit DC3217BY electric (?) issues

September 12, 2017, 12:40 am
$
0
0

Hello to all,

 

I write to you about a series of problems, to tell you the truth, that is pulling me stupid.

In the past winter I bought a used NUC DC3217BY; using my Lacie D2 tb2 hard drive, I noticed that the monitor connected will turn off for a couple of seconds. Sometimes, approaching the cable to the port, little sparks happened.

The hard disk, however, always worked great.

Using it frequently as a "tv" pc, I noticed that also the usb ports made sparks when connecting a device.

Anyway, I have never experienced any problem.

Until this week; trying to update/change my ooss, I burned 2 usb keys and a microSD! which one is irreparable. Everything without particular subterfuge. Insert, puf ... does not read ... "unrecognized device"

I saved two of them, one is no longer read at all.

Once I thought It was my home wirings, but I've tried in different places with no differences. I'm guessing there is current dispersion in the nuc. How I can solve this?

About now I'm not even able to boot by a rescue usb drive!

A last strange sign, connected to a monitor with audio via hdmi, powering the nuc, after the bios POST, trying to boot by usb, I heard an annoying buzz. That was attenuated by inserting usbs, then returning.

Then it will be a casualty, but before all of this nightmare the mPCI wifi card has stopped hooking the 5 GHz band.

Maybe a faulty power supply?

If anyone had any ideas, I would be happy.

Thanks in advance

↧

NUC7I3BNH boot from micro sd reader others OS

May 11, 2017, 12:36 pm
$
0
0

Hi everybody

I just bought nuc 7i3bnh and I´d would like boot with a micro sd card samsung EVO 16gb HC I

i have tested BIOS options refer to boot without succesful. With usb pendrive I installed win 10 pro selecting F10 key

Anybody can help me with bios parameters?

My target is boot with openelec or librelec also

 

Thank in advance

↧

NUC5i7RYH wireless adapter 7265-AC only shows 802.11n

September 9, 2017, 3:33 pm
$
0
0

hello

I have NUC above and my wifi adapter should be able to connect to AC router 5G which it does but only at 802.11n speed which is 300mbps

and the device properties in windows only shows 802.11n channel bandwidth

my router is asus RT-ACRH13

my adapter driver is the latest already 19.60

 

thanks

↧
↧

Question about the Intel Serial IO Driver

September 7, 2017, 8:52 am
$
0
0

What is the use of  Intel Serial IO Driver on NUC 6i5 ?

 

Is there any pin on the NUC mainboard, assigned to the driver of Serial IO UART Host Controller and Serial IO GPIO Host Controller？

 

Is the any possible to connect Intel NUC and Intel Edison via the Serial IO Driver?

 

Can I get a demo program (e.g. C# ) to show the usage?

 

Thanks a lot.

↧

NUC7ixBN Screen Flashing/Flickering when using 4K resolutions

August 2, 2017, 4:42 pm
$
0
0

Hi all,

 

We are aware of this issue and a bug was opened a couple weeks ago.  The developers/engineers are working on finding a solution and I will post any updates and/or solutions here.

 

Thank you for your patience.

↧

Skull Canyon (NUC6i7KYK) can't do >2 channel audio via HDMI?????

August 30, 2017, 8:51 am
$
0
0

Specs: Win10x64 (build ~Jul.1/'17, fully patched), Drivers all patched up, HDMI->TV->SoundBar (via ARC)

 

So. ... Why does my sound-settings limit me to 2-channel only? Everything seems legit but it just won't offer higher than 1995 sound quality. It's really ticking me off. Same setup next to the NUC from Xbox One and my SoundBar shows DTS. From NUC, 2-channel. BAH!!!

 

I've tried:

- uninstalling display driver, reboot, reinstall

- patching HDMI Firmware to February's release

- different cables (all are HDMI2.0 compliant)

- different ports on TV (my TV has a bunch of 30hz ports, and one 60hz)

 

Has anyone else dealt with this and found a resolution?

NUC Stereo Only.png

↧
Search

NUC6I7KYK4 black screen on startup

September 12, 2017, 7:17 pm
$
0
0

My recently purchased NUC6I7KYK4 mini PC has issues with 4K on startup. Mini display port goes to a black screen when a screen item is clicked. HDMI flickers and flashes. I have new cables especially for 4k and the monitor (Acer CB281HK) is brand new. The monitoer starts ok when paired with another  computer. The issue vanishes after a few tries at starting the NUC.

↧
↧

NUC6CAYH Wifi problem

August 24, 2017, 8:56 pm
$
0
0

Hi

Have Debian 9 installed on an NUC6CAYH and having one or two problems that is keeping things from being perfect.  This one seems simple and I hope someone will make me feel like a fool with something I am just not seeing, but I am not able to get Wifi working on this unit.  I have WICD installed which shows no wifi connections.  Rfkill shows nothing switched off.  I have installed the iwlwifi firmware and noticed the iwlwifi-3168-22.ucode file in the /lib/firmware directory.  Not sure where to go from here.  Please enlighten...

Kendew

↧

NUC7i7BNH audio jack popping

July 20, 2017, 12:16 pm
↧

Intel RealSense SR300 runs on NUC6I5SYK but not on NUC7I5BNK/BNH (usb power issues)

July 28, 2017, 7:22 am
$
0
0

In the Intel RealSense forums there are several discussions about power problems with the sensor. This is due to limited power supply from the USB 3 ports.

 

With the 6th gen NUC, the sensor works fine, but with the new 7th gen versions, there seems to be power issues. I tried to connect it to all possible USB ports (even with an adapter to the USB3c). I deactivated all possible power saving options in Windows, but the problem stays the same. The sensor works fine when I connect it to an external active USB hub though - so it's definitely a problem of the NUC. I already updated to the newest BIOS and latest sensor drivers.

 

This was tested on 5 NUCs - 3 of 6th gen and 2 of the 7th gen (all i5 versions).

 

Is there any way to fix this?

↧

3rd monitor not recognized in collage mode

August 3, 2017, 12:40 am
$
0
0

Hi,

 

I made an installation with three video-wall displays and Intel NUC-machine.

 

The Intel Graphics finds the monitors and an extended display can be used with all of them.

 

 

As the installation topology is 1x3 (ie. wanted resolution is 1920x3240px) collage mode is needed.

 

When entering the collage -mode settings, the Intel Graphics finds only 2 displays at the time.

 

 

How can I use all of the three displays in collage mode?

As per the Dell's link below, it is said the third (last) monitor needs to be set to DP1.1.

Can anyone confirm this?

*EDIT* We tried this (last screen in DP1.1 and that didn't work either.

 

Machine:

INTEL NUC BOXNUC7i7BNH Core i7-7567U

 

With Windows 10 HP

 

Displays:

NEC X554UNV (daisy chained with DP-DP cables in DP mode 1.2).

 

Display connection via Targus USB-C - Display Port -adapter.

 

Found this: How to Configure U2415 Monitor Daisy Chaining on Intel HD Graphics | Dell Suomi

↧
↧

anyone know how to use the extra sata port in the nuc7i3bnk without having to leave the nuc opened?

February 22, 2017, 9:53 am
$
0
0

I was told the sata port on the mobo was functional, however, since this nuc is half height there is no room inside for it.

maybe one day I would like to use that port to add a drive for storage.  as it stands now I was told the case has to be left open which is not very practical.  you cannot even run sata and power cable external to the nuc as there are no holes.  sure you can make your own holes but I'm sure it would look terrible.

 

aside from fabricating some kind of extension base plate.....is there any other way?

 

thanks

↧

Can't install official Graphics Driver for NUC7i5BNK

September 13, 2017, 3:35 am
$
0
0

Hi,

 

I just bought a new NUC7i5BNK. I downloaded all drivers and BIOS update from:

 

Downloads for Intel® NUC Kit NUC7i5BNK

 

I was able to install all drivers except one: The official graphics driver! If I try to install them, I got the message, that those drivers can't be installed, because they were not validated for my PC. I then also tried an older version:

 

Download Intel® HD Graphics Driver for Windows® 10 for Intel® NUC Kit NUC7i3BN, NUC7i5BN, and NUC7i7BN

 

But I got the same message.

 

So, what's the problem? I do have a original NUC7i5BNK and those drivers are from the official Intel Website and on the website it says they are valid for my NUC.

 

Regards,

Sascha

↧
Search

INTEL NUCi7 3D MVC ISSUE

March 7, 2017, 8:35 am
$
0
0

Coming from Intel NUC DN2820 I was able to play 3D MVC with Kodi with new Intel Media SDK, I just purchased Intel NUC NUC7i3BNK and 3D playback doesn't work.

 

On the Intel NUC DN2820, the resolution was set 1920X1080p 3D and everything works great

On the Intel NUC NUC7i3BNK either I set the 1920X1080p 3D or  3820X2160p 3D doesn't work

 

The Intel Media SDK was supposed to allow 3D MVC to work, I did some testing and found the HDMI 2.0 connection is the one causing the issue and any NUC with HDMI 2.0 doesn't work/

↧

NUC7I5BNK Power ON from Microsoft Xbox 360 Media Remote not working

September 12, 2017, 6:35 am
$
0
0

I am not sure if it is a bug or a missing feature but since it’s announced that this remote is compatible (NUC Ecosystem Catalog July 2017) should work.

360 Media remote.png

https://www.intel.es/content/dam/www/public/us/en/documents/technical-specifications/nuc-ecosystem-catalog-2017.pdf

 

 

Please add support in BIOS or remove from advertised products as compatible.

 

 

NOTE: some old NUC’s has this support in BIOS:

bios.png

 

However in last generation NUC’s (NUC7I5BNK) this option is missing in BIOS.

 

Related threads:

NUC7I3BNH IR Power On not working

NUC6CAYH switch on with Remote not working

↧
↧

NUC7ixBN Screen Flashing/Flickering when using 4K resolutions

August 2, 2017, 4:42 pm
$
0
0

Hi all,

 

We are aware of this issue and a bug was opened a couple weeks ago.  The developers/engineers are working on finding a solution and I will post any updates and/or solutions here.

 

Thank you for your patience.

↧

Downgrade BIOS on NUC7i3BNH to version 0036

April 26, 2017, 1:48 pm
$
0
0

Hi

 

I got a NUC7i3BNH, which originally came with BIOS 0036.

My plan is to have VMware ESXi on this box (either 6.0U3 or 6.5).

I saw that there was a BIOS upgrade available, so I updated to BIOS 0042.

 

But now the system, won't power off, when doing a shutdown of the ESXi software (tested with both ESXi 6.0U3 and 6.5)

I have been in communication with other people with the precise same hardware, and ESXi versions, running BIOS 0036, where the shutdown/power off works.

 

So I would like to downgrade the BIOS to 0036 again.

But when I try this I just get "Incompatible BIOS Version, Update aborted" using either the F7 option or the IFLASH2 option.

 

When I try to do a Power Button Menu F4 BIOS Recovery, I just get a blank/black screen, and the system is just on, but nothing happens. Left it there for many hours.

I have also tried the BIOS Security Jumper, but the result is the same as the Power Button Menu F4 BIOS Recovery option.

 

How do I downgrade the BIOS back to the original 0036?

↧

NUC7I3BNK not powering up and power button blinking orange

September 12, 2017, 7:17 am
$
0
0

Ok, here's a cool story. I assemble a NUC using compatible RAM and SSD. I then power it on and try to familiarize myself with its BIOS setup when it suddenly shuts down. "Ok..." says I and pretend nothing happened. But, just to be on the safe side (ha-ha), I decide to update the BIOS. And I did so—successfully. Or so i thought. As the updating finished, computer attempted to reboot but appeared to be stuck with orange light flashing (...i think) So I, growing impatient, wisely remove power plug from the outlet, plug it back in, power the computer up and enter BIOS setup checking out it's version. To my surprise the BIOS seems to be updated to the latest version. "Well that was easy" is what I've been thinking when NUC shuts down again. Little did i know i would never manage to power it up again. Since then, whenever I plug it in, unit's power button rapidly blinks in orange. No amount of holding it, pressing it or else does anything. It just keeps blinking. Indefinitely.

So, what I've tried: moving RAM to the other slot, removing it, removing SSD, removing security jumper, removing CMOS battery wires from the connector and waiting, plugging in USB with recovery BIOS, plugging in headphones in order to hear something, ANYTHING. Nothing...

What I'd like to know: is the unit bricked for good or is there still hope left?

 

Last time i edit. I swear.

↧
Viewing all 18668 articles
Browse latest View live
Search
<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>